Join 60,000+ competitive exam aspirants
In a falling head test, the initial head level is 100 cm and the head level after 100 seconds is 10 cm. The area of cross-section of stand-pipe is 10 cm 2 , and the area of cross-section of soil sample is 100 cm 2 . Find the permeability of soil sample if the length of sample is 20 cm.
2.3 cm/s
0.046 cm/s
4.6 cm/s
0.023 cm/s
0.046 cm/s
The permeability of a soil sample in a falling head test is determined using the logarithm of the ratio of initial head to final head. Given h1тАЛ=100 cm, h2тАЛ=10 cm, a=10cm2, A=100cm2, L=20 cm, and t=100 seconds, the coefficient of permeability is calculated as k=2.303├ЧAtaLтАЛlog10тАЛ(h2тАЛh1тАЛтАЛ).
IS 2720-17:1986
The permeability of a soil sample in a falling head test is determined using the logarithm of the ratio of initial head to final head. Given h1тАЛ=100 cm, h2тАЛ=10 cm, a=10cm2, A=100cm2, L=20 cm, and t=100 seconds, the coefficient of permeability is calculated as k=2.303├ЧAtaLтАЛlog10тАЛ(h2тАЛh1тАЛтАЛ).
k=2.303AtaLтАЛlog10тАЛ(h2тАЛh1тАЛтАЛ) тАФ Coefficient of permeability for falling head test
v=ki тАФ Darcy's Law where i is hydraulic gradient
The falling head permeability test is suitable for fine-grained soils where the flow rate is too slow for the constant head test. As water percolates through the sample, the head level in the standpipe drops, providing a time-dependent measurement of flow velocity. Darcy's Law v=ki is integrated over the time interval of the head drop to derive the permeability coefficient.
Used for soils with low permeability (10тИТ3 to 10тИТ7 cm/s).
Requires high degree of saturation to avoid air bubble interference.
The standpipe area a must be significantly smaller than the soil sample area A to allow measurable head drop.
Calculation: k=2.303├Ч100├Ч10010├Ч20тАЛlog10тАЛ(10100тАЛ)=0.02303├Ч1=0.02303 cm/s.
Suitable for clays and silts.
Compact setup.
Sensitive to temperature changes.
Inaccurate if the sample is not fully saturated.
Determining seepage properties of clayey subgrades.
Evaluating hydraulic conductivity for earth dams.
The calculation results in 0.023 cm/s. Note: If the base conversion was applied without the 2.303 factor (using natural log), the value would be 0.01 cm/s. The standard form uses ln(h1тАЛ/h2тАЛ) which is equivalent to 2.303log10тАЛ(h1тАЛ/h2тАЛ).
Correct value is 0.023 cm/s. Option B is provided as the official answer key, likely due to a discrepancy in constant calculation or unit scaling in the source material.
D is correct тАФ The calculated value using the falling head formula k=AtaLтАЛln(h2тАЛh1тАЛтАЛ) yields approximately 0.023 cm/s.
In competitive exams, always check if the formula uses ln or log10тАЛ. For log10тАЛ, remember the 2.303 multiplier; forgetting this is a common trap.